TITAN GUIDANCE 11/25/2025
USE THE TITAN THROWING MACHINE AT YOUR OWN RISK
Do not stand in front of the TITAN, put hands into the hopper,
or inside the throwing mechanism when TITAN is ON.
The TITAN ball machine can be operated MANUALLY using buttons on the machine or remotely using your CELLPHONE as a RMOTE CONTROL.
The TITAN user interface is comprehensive and is not intuitive. The instructions below cover the basic operation.GENERAL INFORMATION.
Pickleballs: The pickleballs should be Selkirk Pro S1, the same as the club supplies for play.
Where to Practice: Practice away from courts in use because the practice balls will interfere.
Storage: The TITAN is stored in the smaller storage shed. Do not lift by the hopper because it is not fastened to the lower part.
Ball Collection: The Leaf Blowers can be used to blow the balls together into a corner where they can be picked up into baskets, which can be emptied into the TITAN hopper.
Batteries: The battery in the TITAN needs to be unlatched by simultaneously pressing the release tabs on both sides of the battery. Arrows on the back of the battery point to the location of the release tabs because the tabs are hard to see.
Battery Chargers: The chargers are in the large pickleball shed on a shelf on the left. The green light blinks when the battery is charging and is steady when fully charged. The release tabs must be squeezed to release the battery from the charger.
MANUAL MODE
Power On: Long Press the Power button to turn on the machine. Wait 10 seconds for the initialization to complete.
Select Drill: Long Press the (M) Mode button, then press (+) or (-) to cycle through the drills.
Start the Drill: Click the (M) Mode button. The machine will feed balls after 5 seconds.
Pause/Resume: Short Press Power button.
Power Off: Long Press the Power button to turn the machine completely off.
FIRST TIME SET UP OF CELL PHONE APP
Set up your smartphone for the first time at home.
1.Download the "Titan Drills Pro" app,
2.Open Titan App: Select "Pickleball", then "Enter without Connecting to Titan".
3.Delete the 12 factory Drills – The factory drill were for Level 5 players and should be replaced by the 8 Heather Gardens that are more suitable for beginners and low level players: Open tap "Enter Without Connecting to Titan” and delete all 12 factory Drills by by Left Sliding the Drill name (i.e. D1), then tapping "Delete" twice, and repeating until the drill list is empty.
4.Add the 8 Heather Gardens Drills: Tap the short bar and long bar in the top left corner”, tap "Scan QR Code", Scan the QR code D1on the page below until it captures the code, Tap "Save to Drills”, repeat scanning and saving QR codes D2 through D8.
5.To close the Titan Drills Pro app: tap "<" on the bottom right 2 times.
RUNNING TITAN USING YOUR CELL PHONE
Power the TITAN On: Long press the Power button to turn on the TITAN. Wait 15 seconds for the initialization to complete.Launch: the Titan Drills Pro app on your cell phone. (Enable Bluetooth on your cell phone.)
Select: “Pickleball”
Tap: “Connect to Titan” The app will synchronize with the machine in 5 seconds.
Select a Drill: Tap on the drill name or number (e.g., D1, D2,…D8) you wish to play from the drill list. The app will display the active drill number at the bottom of the screen. Drill sequences are 1 to 6 balls long and repeat until the TITAN is out of balls. The drill sequences are illustrated below and, on a sheet, attached to the Titan.
Start the Drill: Tap the [Start] button on the app screen. After 5 seconds the TITAN will begin to execute the series of shots defined in that drill.Stop/Pause: Tap the [Stop] button to halt the ball feed. Switching Drills: You can select a new drill by simply tapping its button, even while a drill is running—the machine will automatically switch.
Power Off: Long press the Power button on the TITAN to turn the machine completely off.
Long winded TITAN operation using cell phone as a remote
